Thursday, September 6, 2012

Cheap Wireless TTL? Aokatec AK-TTL Review


The Aokatec AK-TTL radio trigger is a wireless radio trigger that is supposed to be cross-compatible with Canon, Nikon, Pentax and Sony (no word on Olympus). The price for a transmitter and receiver kit: $109.99.

I've never heard of Aokatec before (until a comment posted by a reader, Ricardo Rodrigues, about Aokatec's version of the Nikon SG-3IR infrared panel). I've also been disappointed many times when buying products from unknown companies, especially when they make incredible claims, and even more so when the price is a fraction of equivalent products from more established manufacturers.
How well did it perform? Hit the jump.

OVERVIEW
Currently, there are several available systems that promise wireless TTL. First, most camera brands offer their own native wireless TTL system. Until recently, all of those systems worked through infrared light. Commander units could communicate with slave flashes through coded pulses of visible light (or infrared light). The problem with this system is that sometimes, the slave flashes could not detect the light pulses sent out by the commanders -- either because the ambient was too bright, or the flash was too far away. It's only slightly better than line-of-sight (it's better than LOS because the pulses can bounce off from nearby surfaces).

Third parties came up with radio-based wireless flash systems. At first there were just simple manual triggers which offered much greater reliability than optical systems (e.g. PocketWizard, eBay povertywizards, etc.) but could not be adjusted and were manual only (no TTL). Next came triggers that allowed manual power adjustment (e.g. Radiopopper JrX Studio). Then we had remote-adjustable radio triggers with both TTL and manual capability (Radiopopper PX, Pocketwizard FlexTT5 and MiniTT1). However, these systems were very expensive. Some companies produced less expensive TTL triggers but many of them had significant limitations (some functioned essentially like a TTL cord, except wireless). Then, a few months ago, Canon introduced flashes with a built-in radio-based wireless TTL system.
So, the market had several systems that were either cheap and didn't do exactly what I wanted, or did what I wanted but were very expensive. Then came the Aokatec AK-TTL. It was announced earlier this year but became available less than 2 weeks ago.

AOKATEC AK-TTL
The Aokatec AK-TTL works with your camera's native infrared wireless flash system. In principle, it appears to work similarly with the Radiopopper PX system. The transmitter is positioned close to the commander flash and detects the electromagnetic noise emitted by your commander flash when it flashes, then the transmitter sends out a radio signal that mimics the flash pulse pattern. The radio signal is received by the receiver unit which re-broadcasts the pulse pattern as an infrared signal, directly to the infrared receiver of the slave flash.

With the promised specs (cross-compatibility with Canon, Nikon, Pentax and Sony) and seemingly no weaknesses, the Aokatec AK-TTL seemed really fishy. There had to be a catch. So as much as I wanted to, I didn't order it. Fortunately, photographer Aaron Burns bought one to test. He was using a Nikon D5100, and tested the following commanders: Nikon SU-800 dedicated infrared commander, Nikon SB-700, and Nissin Di866 II. For the slaves, he tested the aforementioned SB-700, Di866 II and Oolong SP-660 II. To my surprise, he reported that it worked for him. The only downside he noted was that the range was lower than advertised (75m instead of 100m).

After I read Aaron's review, I ordered a set on eBay. Fortunately, one of the sellers (ebay user gpslot) is based in California, which increased my confidence because it would be easier to return the product if it didn't work (sometimes foreign-based sellers rely on the high cost of returning a product as a way of discouraging returns).

I'd like to build on Aaron's excellent review by adding some more info. Aaron's tests were very thorough but there were a few questions unanswered, such as: would popup commanders work? What about wireless HSS work?

I found out that the seller is based in Los Angeles like me, so I got the package within just a couple of days of ordering it. The kit came as a separately boxed transmitter (TX) and receiver (RX).

THE TX PACKAGE
The TX package includes the transmitter, a lanyard, 2 pairs of velcro stickers and an infrared panel with an attachment for mounting the TX unit on the IR panel.

THE RX PACKAGE
The RX package includes the RX unit, the infrared repeater, a 3.5mm to 3.5mm sync cable, a 3.5mm to PC sync cable, a lanyard and two Livestrong wristbands bright yellow rubber bands. On my package, I did not see a rubber cutout, which was included in Aaron's package. The cutout would have been a small rubber sticker to be attached to the flash to help position the IR repeater and increase the friction between the repeater and the flash.

THE TX UNIT AND RX UNIT
Externally, the transmitter and receiver appear identical. The only difference externally appears to be the label. I attached the lanyard to the receiver to make it easier for me to distinguish between the two in the field when it's dark or I'm in a hurry. Physically, the triggers are reasonably small (about the size of a pack of TicTac candies) and very light.
On the face of the unit is an LED light, a test button and a 16-channel switch.
- When the unit is turned on, the LED pulses with a green light every 4 seconds or so. When the TX transmits or the RX receives a signal, then light becomes red. The red light seems brighter than the green light, although both are visible to me in daylight.
- Besides being used to confirm that the units are communicating, the test button can be used to wake up your slave flash if it goes into standby or sleep mode.
- The channel selector has clear detents. It is not likely to be nudged accidentally into a different channel. One issue is that the arrow for the channel selector is tiny, so it may be hard to see whether a channel is set to a particular number or the number on the opposite side.
At the top of the unit is a cover for the battery. It feels secure, though as noted in Aaron's review, the clips for the cover are very thin and could easily snap off. Both TX and RX are powered by two AAA batteries each. On my package, batteries were not included. The labels for the required polarity for the batteries are a little hard to see. I just have to remember that the battery closer to the middle has the + end pointing inside the unit.
The bottom is a plastic foot for a regular ISO hotshoe with a flash triggering pin. (I don't have a Sony version but to my understanding it has a foot for the Sony/Minolta hotshoe.) The foot has no collar or other mechanism to lock it in position on a hotshoe other than by friction. However, when attached to a hotshoe, it felt snug, not like it was going to fall off.

On one side of the unit is a switch between manual mode, off, and auto (i.e. wireless adjustment mode). On the other side of the unit is a 3.5mm jack. The switch is ok although there is a bit of 'play' so the switch feels slightly flimsier than the rest of the unit.

INFRARED PANEL
The TX package includes an IR panel, which at first glance looks like a clone of Nikon's SG-3IR infrared panel. If you're new to wireless flash, the function of the IR panel is to block the visible light from the commander's pulses while allowing the infrared spectrum of the signal to pass through. For conventional wireless flash systems, this makes sure that the popup commander is not contributing to the exposure. Another benefit is that it blocks the flash pulses that often cause subjects to blink. (With the IR panel blocking the visible flash pulses, all the subjects will see is that the panel will flash a bit red, which in my experience doesn't cause them to blink.)
With the Aokatec AK-TTL system, the panel arguably should block all of the light (even the IR portion) so that the receivers won't get confused with competing signals from the repeater and the popup commander. However, the Aokatec panel does allow the IR portion to pass through. I am considering sticking something at the back of the Aokatec panel to block even the IR portion. However, by allowing the IR portion to pass through I can mix the radio-based AK-TTL triggering and the regular optical triggering.
The Aokatec panel (left, with attachment shown) and the Nikon SG-3IR
Notwithstanding the many similarities between the Aokatec and Nikon panels, there are a few significant details that distinguish the Aokatec panel from the SG-3IR:

1. One of the first things I noticed is that the Aokatec panel has a more flimsy movement compared to SG-3IR. It is possible that if the Aokatec panel is flipped many times repeatedly, the hinge might get worn to the point that the panel might not stay up by itself. However, I'm just speculating - it hasn't happened yet and I suspect it would take a while for that to happen.

2. The Aokatec's panel seems to be made of a different kind of plastic, although it appears just as opaque as that of the SG-3IR. I haven't seen any difference in ability to block visible light.
3. A distinct feature of the Aokatec panel is that it includes a removable attachment that allows an AK-TTL TX unit to be mounted on the panel.
4. A plus for Canon shooters is that the Aokatec foot has a thinner portion designed to avoid pushing down the TTL pins on Canon hotshoes. (Otherwise when those pins are pushed down, Canon cameras think there is a Canon TTL flash attached.) By contrast, Canon shooters wanting to use the SG-3IR have had to shave off a portion of the SG-3IR's foot to avoid pushing down the Canon TTL pins.
5. Another difference is that the Aokatec's locking pin is rounded, whereas that of the SG-3IR is sharp. Some SG-3IR users have commented that the SG-3IR is hard to remove from a hotshoe (in fact some users have removed the locking pin). With the Aokatec's rounded pin, it is easier to remove from a hotshoe, while still being secure.
USING THE AK-TTL SYSTEM
To use the AK-TTL system, you first attach the TX unit close to the commander. If you're using a popup commander, then this is done by mounting the TX unit on the included IR panel.
If your commander is instead an external flash or dedicated IR commander, you can attach the TX unit to your commander flash using the included velcro pads.
As previously mentioned, the RX unit includes an IR repeater. The repeater is quite small though somewhat thick. The side with the emitter has rubber padding to increase friction with the flash surface.
You plug one end of the repeater to the sync port of the RX unit. You then locate the IR sensor of the slave unit. The sensor is not always facing the front. On the SB-800, it is a small round and dark window on the side of the flash, near the battery door.
You attach the repeater over the IR sensor using the included rubber band.
Personally I don't like the rubber band because it looks way too conspicuous. I am also concerned that the rubber may dry out and snap. Instead of the rubber band, I used two velcro cable ties linked to each other. The cable tie is attached to the cable, making it less likely that I'll lose it. I think it also looks better than the rubber band.
From there all you have to do is put the slaves on wireless mode. Some reminders
- The slaves should be in the same channel (1, 2, 3 or 4) as the commander, and note the group (A, B or C).
- The TX and RX units have to use the same radio channel (1 through 16).
- Make sure the slaves aren't asleep or in standby.
- Some 3rd party slave flashes don't have HSS. If you exceed the sync speed, the commander will use the HSS protocol which the slave won't understand so it won't fire.
The AK-TTL can also be used as a simple manual radio trigger. To do that, you just switch both units to M mode and connect the receiver to the slave using the 3.5mm to PC cable or the 3.5mm to 3.5mm cable. I tested the PC cable and was able to trigger the SB-800.
COMPATIBILITY TESTS
I tested the AK-TTL system with the following commanders:
- Nikon D70 popup (note: the D70 wireless flash is limited to channel 3, group A only. You cannot change the channel or control any other group).
- Nikon D90 popup
- Fuji S5 popup
- SB-800 as commander
I tested them with the following slaves:
- Nikon SB-800
- YongNuo YN-560EX
Based on my tests, the AK-TTL does work just as well as Nikon's CLS (Creative Lighting System) AWL (Advanced Wireless Lighting). With two caveats (discussed below), the slaves functioned to the same extent as if they had been controlled by the optical signal from the commander. I could use TTL mode, adjust FEC up and down, change to manual mode, and adjust manual power levels.
Among the tests I did, which worked (feel free to check out the exif on the samples):
Yongnuo YN-560EX. The fact that this worked was a relief, because I want to use the YN-560EX as an inexpensive wireless adjustable slave.
Wireless HSS: I tried Wireless HSS at 1/8000 shutter speed and it worked. I tested it with the Fuji S5 popup as commander and a Nikon SB-800 as slave.
Non-HSS sync speed: I tested up to 1/500 shutter speed (using Nikon D70).
Mixed optical with AK-TTL radio:
I tested the SB-800 as commander, with another SB-800 as AK-TTL radio slave in Group A and YN-560EX as Nikon CLS AWL optical slave in Group B.
Inline image 1

Panasonic Lumix LX-5: :Just for fun, I experimented with the LX-5's popup flash as well.  I used an SB-800 as a slave in SU-4 mode.  I covered the SB-800 with a thick comforter to make sure it was not receiving an optical signal from the popup flash.  When I mounted the TX unit on the hotshoe using the Aokatec panel, the system did not trigger (the TX unit probably could not detect the electromagnetic noise from the small popup flash).  However, when I held the TX beside the popup flash, it was able to trigger the SB-800 all the way to the maximum 1/2000 sync speed.

In short, as far as I can tell, the AK-TTL performs just as promised. About those caveats I mentioned earlier:
1. Interference. If the slave receives a signal from the repeater as well as the optical signal of the commander, it might not fire. One solution is to face the sensor away from the commander.
2. Repeater placement. On my first couple of tries with the YN-560EX, it did not fire. I don't know for sure if it was partly caused by interference but one thing I did is to adjust the IR repeater position slightly to the left of center, and from there the 560EX worked fine. The 560EX's sensor is a large opaque panel, so it's hard for me to tell the optimal position for the repeater.
If I had to nitpick the AK-TTL, I think the weakest part of the system is how the IR repeater attaches to the slave flash.
- First, it might not completely block the flash from still receiving the optical wireless signals, resulting in failure due to interference.
- You also need to know where the sensor is on the slave flash. On the SB-800 it's easy. On the YN-560EX, I am hoping I have it figured out. I would hate to be on an assignment and have the triggering fail because the repeater is slightly out of position.
- Placing the repeater can take a few seconds. I think the velcro cable tie makes this a bit easier.
- The IR repeater might be moved out of position if the flash is jostled hard enough. Besides losing the signal, the RX unit could fall if it is just dangling from the IR repeater.
- It's possible you might forget, lose or break the rubber band that you're using to secure the repeater, which could make the system temporarily unusable (then again, gaffer tape could come to the rescue).
Also, pls. note that I have not yet tested:
- long term durability
- battery life in the field
- multiple RX units (I have another RX unit on order and will be posting about this soon)
- whether it works on Canon, Sony, Pentax or Olympus.
You can tell that those are really minor gripes, and those are the worst things I can say about the AK-TTL. In other words, I FRIGGIN LOVE IT. It works as well as I hoped and the price is just right. This is now my preferred radio flash trigger and would recommend it. I previously envied Canon shooters for having a radio-based wireless flash system. Now? Not as much. :) Coupled with the availability of inexpensive wireless-capable flashes such as the Yongnuo YN-560EX, adjustable radio-based wireless flash systems are now accessible to virtually everyone [even Pentax shooters :) ]!



25 comments:

  1. I would agree with your comments above

    " I FRIGGIN LOVE IT TOO " !!!!!!

    I'm using it with several Nissin Di866 flashes as well as a couple of Nissin Di622 flashes.

    The Nissins ahve been rather weak when it comes to off camera flash, their sensors arent the best .. with the AK-TTL that does not matter anymore.

    Very please with the product so far and thanks for publishing an informative review.

    ReplyDelete
    Replies
    1. Sorry for the late reply... Thanks that's awesome to know that it works with the Nissin Di866 and Di622 as well!

      Best regards,
      Mic

      Delete
  2. Best kept secret TTL Wireless trigger.

    ReplyDelete
    Replies
    1. Yes I agree! That's why I hurriedly sold my JrX units at a loss. It was still more than enough to buy Aokatecs as replacements :)

      Best regards,
      Mic

      Delete
  3. been a while since the review.. just would like to know how these triggers holding up? are they still reliable?

    been searching for an affordable nikon TTL triggers for months, i really hope this won't disappoint.

    btw, will this trigger work with yongnuo 565ex flashes? or any ttl flash brands?

    thanks!

    ReplyDelete
    Replies
    1. Hi! Yes the triggers are still working. Haven't encountered problems with them as long as I make sure the slave flash is not "seeing" the popup flash or commander. This is easy with the SB800 due to the small window, just slightly more difficult with the YN560EX due to its large window. Anyway, when I get that done right, then it is reliable.

      I have not personally tried it with the 565EX but I believe it should work. As for other brands, as noted above in one of the comments, it works with the Nissin Di866 and Di622.

      With these made-in-China triggers, we really don't know how long they will last. Nonetheless, I'm pleased enough with the Aokatec that I got another slave unit, sold off my JrX Studio set, and will purchase more slave units as the need arises. I suggest buying them from a seller from your country if possible (note: there are US sellers). I bought mine from a CA-based seller even though it was cheaper to buy from China.

      Best regards,
      Mic

      Delete
  4. thanks for the quick response.. i've actually been looking around for the past couple days but couldn't find one locally (U.S.).. if i can't find one til weekend i might just risk buying from china.. thanks again for responding and for the advice :)

    ReplyDelete
  5. Hi Mic

    I have just tried my new YN560EX ( decided to buy one thanks to your testing! )and it works great, and just to confirm what you have already said, it is a little tricky finding the optical sensor in behind that large window.

    I'm actually quite keen on aquiring an SU-800 to control my 2 x Di866's and my 1 x YN560EX, seems like a great way to have TTL flash and manual control at your fingertips.

    ReplyDelete
    Replies
    1. Hi R.Campbell! sorry for the late reply. Glad to know the 560EX and aokatec are working well for you. I think the Aokatec could work with an SU-800, though I haven't tried it yet.

      Best regards,
      Mic

      Delete
  6. Hi Mic, I just wanted to check if you are still using this radio triggers? I am strongly considering this after looking at other options (Odins, 622n, PW and RP) thanks in advance.

    ReplyDelete
    Replies
    1. Hi there! I have not had to use radio TTL triggers for a while (when I did, I used these triggers). They are still as good as they have been.

      However, now that the YN-622 is available for Nikon, that *might* be better than the Aokatec in some ways, because the YN-622 supposedly allows high speed sync even for non-HSS strobes like alien bees. I haven't used the YN-622 to confirm that, but if that's true, then that's an advantage over the Aokatec. The YN-622 is also easier to use (just slide the flash into the hotshoe vs. strapping the emitter to the infrared window).

      On the other hand, one advantage of the Aokatec over the YN-622 is compatibility with cheaper speedlights. For example, the YN-622 cannot be used with the 560EX whereas the Aokatec can.

      Best regards,
      Mic

      Delete
  7. Hi Mic, I actually read and followed the 622n and waited for the day it was released. However reviews are a mixed bag. I heard ratios didn't work so well. I read from a review that you can't fire on-camera flash on TTL while firing off cam flashes and lastly flash power adjustment is through push button combination on the transmitter. Odins would have been great as well but I wanted the option to fire on camera flash as well.

    I ended up getting the Aokatec based on your review and a few others on the internet. I'm a huge CLS user and really enjoyed the convenience of adjusting flash power settings remotely in-camera.Aokatec just extends this feature in radio format. I also liked that you can fire multiple flashes on different groups with just one receiver. Lastly, ebay price at $150 plus shipping for 1 transmitter and 3 receiver couldn't be beat although i ordered mine from Amazon for a little bit over $200 for the same set-up. Thanks for the tip on the velcro ties.

    ReplyDelete
    Replies
    1. Thanks! Yes I've heard some complaints about the 622n. For me the biggest difference between them is the ability to sync at 1/8000 with a studio strobe such as Alien Bees, and the ease of mounting. However, given the spotty reliability of the YN-622n, I'm keeping my Aokatecs.

      Best regards,
      Mic

      Delete
  8. Aokatec's are so awesome!! It is too good to be true. I'm still looking at gotcha's or some kind of a catch. The only downside I'm experiencing is finding an equivalent black rubber band to replace the yellow bands. I tried your velcro ties tip but they don't seem to hold and stay on the flash making the optical cable misaligned overtime. I think the rubberband is way faster and easier to put on, i just want a black one.

    ReplyDelete
    Replies
    1. Yes I think they're pretty good. My only wish for Aokatec is some way to integrate them with Alien Bees. I still haven't been able to do that (unless I use a camera body with a PC sync port, then connect the PC sync to a cybercommander).

      As for black rubber bands, I see some on Amazon. One of them called Roadpro is UV and ozone resistant, so perhaps it's less likely to crack over time.

      Best regards,
      Mic

      Delete
    2. Thanks Mic, yes i did see the Roadpro 7 EPDM Rubber Bands before from Amazon. I guess that's my last resort now seeing that I was not able to find it around from different stores. My only concern is there is no dimension on those rubber bands, they may be too big or too small, so no way to find out until i order and get the actual bands.

      I've tried the Aokatec's on my recent shoot and it worked flawlessly. However, I did test it to its limits the other day and I have found some situations that it did misfire ie. no line of sight and i think i was about 100 steps away (approx 75m?) from the receiver.

      Delete
  9. Canon 60D master pop up flash and Nissin 866 doesn't work. Master Nissin 866 remote nissin 866 doesn't work I am very disappointed

    ReplyDelete
    Replies
    1. That sucks... Sorry to hear that.

      Did you try all the channels? Some channels are more susceptible to radio interference. Is the receiver blinking when you press the test button on the transmitter?

      Best regards,
      Mic

      Delete
    2. Yes blinking . it's very strange. I tried everything. M mode working.. I informed before buying and I was convinced compatibility with Nissin 866. That was also the reason I chose Aokatec

      Delete
    3. For Canon Compatible Flashes:

      Camera with pop-up master flash: Canon 600D 650D 60D 7D
      Master Unit/Flash: Canon ST-E2 550EX 580EX 580EXII 600EX-RT 90EX and Nissin Sigma Metz compatible flashes

      Remote/Slave Flash: Canon 550EX 580EX 580EXII 600EX-RT 420EX 430EX 430EXII 320EX 270EXII and Nissin Sigma Metz compatible flashes

      Write clearly it works but doesn t work

      Delete
  10. Canon 60D master pop up flash and Nissin 866 doesn't work. Master Nissin 866 remote nissin 866 doesn't work I am very disappointed

    ReplyDelete
  11. Yes receiver blinking red.I tried everything. It's weird for that from what I read it should work. For this reason we chose aokatek

    ReplyDelete
  12. Hi Mic

    I'm a big fan of the Aokatecs and use them quite a lot. I am starting to use them a lot with Studio Flash and their ability to deliver fast manual sync or Hypersync with Studio flashes.

    I think you might be interested in the thread in the Strobist group where I outline the technique I used to achieve Hypersync with a very basic studio flash.

    ReplyDelete
    Replies
    1. Thanks my friend. When you say Strobist group, you mean the one on flickr? I went to search there and did not see the thread. Can you share the link? Thanks in advance!

      Best regards,
      Mic

      Delete
    2. I did post the link, but I think either this website or my browser blocked it .. will try again.

      http://www.flickr.com/groups/strobist/discuss/72157639176900323/#comment72157639424928845

      Delete

Thanks for your comment. It will be published as soon as we get a chance to review it, sorry for that, but we get lots of spam with malicious links.